Differences

This shows you the differences between two versions of the page.

--- fadercore_-_vlr-3x8but [2014/07/27 21:55] – novski
+++ fadercore_-_vlr-3x8but [2014/07/27 22:15] – novski
@@ Line 35: / Line 35: @@
   * 2x10pin Header, 517-30310-6002
   * 5x100nF,594-K104K15X7RF53K2
-  * 2x10k, 774-77061103P
+  * 2x10k Network, 774-77061103P
-  * 3x220R, 652-4816P-T1LF-220
+  * 3x220R Array, 652-4816P-T1LF-220
   * 1x74HC165D, 771-HC165D652
   * 4x74HC595D, 771-74HC595D
-  * 24xLED RGB,
+  * 24xLED RGB, 604-WP154A4SUREQBFZW
+  * 24x1N4148, 512-1N4148TR
-Project Order Basket on Mouser: [[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=a6dbae9ab7]]
+Project Order Basket on Mouser: [[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=1f42b04e6d]]
-The PCB is available under: [[http://vlrlab.com/lang/17-8enc.html]]
+The PCB is available under: [[]]
-  * 8 Encoder, 652-PEL12T4226FS1024 **not on Projectlist because i deliver cheaper and with cap included..**
-The Encoder on VLRlabs.com [[https://www.vlrlab.com/encoder/13-bourns-rgb-led-encoder.html]]
@@ Line 55: / Line 53: @@
 ==== Prepare the PCB ====
-Start with the SMD parts and then go on the the conventional parts also on the Bottom side. Don't forget the R11,12,13.
+Start with the SMD parts and then go on the the conventional parts also on the Bottom side.
-Then go on with the Topside and the LEDs before soldering the Encoder as last.
+Then go on with the Topside and the LEDs.
 Check the Connections with a Lens.
 ==== Prepare the Connection ====
-Connect the core on J8/9 to J1 of the VLR-8Enc board.
+Connect the core on J8/9 to J1 of the VLR-3x8But board.
 ==== Test it in MIOS ====
+\\
-To make it work with MIOS .NGC  File we need to know how the shift-registers are connected.
+To make it work with MIOS .NGC  File we need to know how the shift-registers are connected.\\
+\\
 **Inputs:**\\
-# Encoder         1-4\\
+# Switch Columns  1-8\\
-# Encoder         5-8\\
+\\
-# Encoder Button  1-8\\
 **Outputs:**\\
-# RED Shaft LED   1-8\\
+# ROW Outputs     1-6\\
-# GREEN shaft LED 1-8\\
+# RED LEDs        1-8\\
-# BLUE shaft LED  1-8\\
+# GREEN LEDs      1-8\\
-# LED Ring Row    1-8\\
+# BLUE LEDs       1-8\\
-# LED Ring Selct  1-8\\
+\\
-# LED Ring Select 9-11\\
+Assuming that the VLR-3x8But is the first device on the chain of J8/9 we need to configure it like this:\\
-Assuming that the VLR-8Enc is the first device on the chain of J8/9 we need to configure it like this:
 \\
 RESET_HW\\
@@ Line 86: / Line 80: @@
 LCD "%C"\\
 \\
-# Encoder configuration\\
+LCD "@(1:1:1)OLED1"\\
+LCD "@(2:1:1)OLED2"\\
+LCD "@(3:1:1)OLED3"\\
+LCD "@(4:1:1)OLED4"\\
+LCD "@(5:1:1)OLED5"\\
+LCD "@(6:1:1)OLED6"\\
+LCD "@(7:1:1)OLED7"\\
+LCD "@(8:1:1)OLED8"\\
 \\
-ENC n=  1   sr=1 pins=0:1   type=detented2\\
+# In this demo we configure individual brightness levels for the LEDs from EVENT_BUTTON events\\
-ENC n=  2   sr=1 pins=2:3   type=detented2\\
-ENC n=  3   sr=1 pins=4:5   type=detented2\\
-ENC n=  4   sr=1 pins=6:7   type=detented2\\
-ENC n=  5   sr=2 pins=0:1   type=detented2\\
-ENC n=  6   sr=2 pins=2:3   type=detented2\\
-ENC n=  7   sr=2 pins=4:5   type=detented2\\
-ENC n=  8   sr=2 pins=6:7   type=detented2\\
 \\
-# LEDring configuration\\
+LCD "@(1:10:1)RGB Demo #2"\\
-DOUT_MATRIX n= 1  rows=16 mirrored_row=0 inverted_sel=1 sr_dout_sel1= 4  sr_dout_sel2= 0 sr_dout_r1= 5 sr_dout_r2= 6\\
 \\
-# Encoder events\\
+DIN_MATRIX  n=1  rows=4  sr_dout_sel1=1  sr_din1=1                     button_emu_id_offset=1001\\
-EVENT_ENC id= 1  fwd_id=LED_MATRIX:1   type=CC chn= 1 cc= 24  lcd_pos=1:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
+DOUT_MATRIX n=1  rows=4  sr_dout_r1=2    sr_dout_g1=3 sr_dout_b1=4     led_emu_id_offset=1025\\
-EVENT_ENC id= 2  fwd_id=LED_MATRIX:2   type=CC chn= 1 cc= 25  lcd_pos=2:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
-EVENT_ENC id= 3  fwd_id=LED_MATRIX:3   type=CC chn= 1 cc= 26  lcd_pos=3:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
-EVENT_ENC id= 4  fwd_id=LED_MATRIX:4   type=CC chn= 1 cc= 27  lcd_pos=4:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
-EVENT_ENC id= 5  fwd_id=LED_MATRIX:5   type=CC chn= 1 cc= 28  lcd_pos=5:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
-EVENT_ENC id= 6  fwd_id=LED_MATRIX:6   type=CC chn= 1 cc= 29  lcd_pos=6:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
-EVENT_ENC id= 7  fwd_id=LED_MATRIX:7   type=CC chn= 1 cc= 30  lcd_pos=7:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
-EVENT_ENC id= 8  fwd_id=LED_MATRIX:8   type=CC chn= 1 cc= 31  lcd_pos=8:1:2 label="^std_enc" LED_MATRIX_PATTERN=2\\
 \\
-# Encoder Buttons\\
+# These button functions forward their value also to LEDs\\
+# it's possible to set the rgb levels in the button event, it will be forwarded as well!\\
 \\
-EVENT_BUTTON   id=117     hw_id=17   fwd_id=LED:8  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=1:1:3 label="R^std_btn"\\
+EVENT_BUTTON  id=1001  fwd_id=LED:1025  type=NoteOn key=36 chn=1  rgb=15:0:0 lcd_pos=1:1:2 label="^std_btn"\\
-EVENT_BUTTON   id=117     hw_id=17   fwd_id=LED:16 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=1:1:4 label="G^std_btn"\\
+EVENT_BUTTON  id=1002  fwd_id=LED:1026  type=NoteOn key=37 chn=1  rgb=15:0:0 lcd_pos=2:1:2 label="^std_btn"\\
-EVENT_BUTTON   id=117     hw_id=17   fwd_id=LED:24 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=1:1:5 label="B^std_btn"\\
+EVENT_BUTTON  id=1003  fwd_id=LED:1027  type=NoteOn key=38 chn=1  rgb=15:0:0 lcd_pos=3:1:2 label="^std_btn"\\
+EVENT_BUTTON  id=1004  fwd_id=LED:1028  type=NoteOn key=39 chn=1  rgb=15:0:0 lcd_pos=4:1:2 label="^std_btn"\\
+EVENT_BUTTON  id=1005  fwd_id=LED:1029  type=NoteOn key=40 chn=1  rgb=15:0:0 lcd_pos=5:1:2 label="^std_btn"\\
+EVENT_BUTTON  id=1006  fwd_id=LED:1030  type=NoteOn key=41 chn=1  rgb=15:0:0 lcd_pos=6:1:2 label="^std_btn"\\
+EVENT_BUTTON  id=1007  fwd_id=LED:1031  type=NoteOn key=42 chn=1  rgb=15:0:0 lcd_pos=7:1:2 label="^std_btn"\\
+EVENT_BUTTON  id=1008  fwd_id=LED:1032  type=NoteOn key=43 chn=1  rgb=15:0:0 lcd_pos=8:1:2 label="^std_btn"\\
 \\
-EVENT_BUTTON   id=118     hw_id=18   fwd_id=LED:7  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=2:1:3 label="R^std_btn"\\
+EVENT_BUTTON  id=1009  fwd_id=LED:1033  type=NoteOn key=52 chn=1  rgb=0:15:0 lcd_pos=1:1:3 label="^std_btn"\\
-EVENT_BUTTON   id=118     hw_id=18   fwd_id=LED:15 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=2:1:4 label="G^std_btn"\\
+EVENT_BUTTON  id=1010  fwd_id=LED:1034  type=NoteOn key=53 chn=1  rgb=0:15:0 lcd_pos=2:1:3 label="^std_btn"\\
-EVENT_BUTTON   id=118     hw_id=18   fwd_id=LED:23 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=2:1:5 label="B^std_btn"\\
+EVENT_BUTTON  id=1011  fwd_id=LED:1035  type=NoteOn key=54 chn=1  rgb=0:15:0 lcd_pos=3:1:3 label="^std_btn"\\
+EVENT_BUTTON  id=1012  fwd_id=LED:1036  type=NoteOn key=55 chn=1  rgb=0:15:0 lcd_pos=4:1:3 label="^std_btn"\\
+EVENT_BUTTON  id=1013  fwd_id=LED:1037  type=NoteOn key=56 chn=1  rgb=0:15:0 lcd_pos=5:1:3 label="^std_btn"\\
+EVENT_BUTTON  id=1014  fwd_id=LED:1038  type=NoteOn key=57 chn=1  rgb=0:15:0 lcd_pos=6:1:3 label="^std_btn"\\
+EVENT_BUTTON  id=1015  fwd_id=LED:1039  type=NoteOn key=58 chn=1  rgb=0:15:0 lcd_pos=7:1:3 label="^std_btn"\\
+EVENT_BUTTON  id=1016  fwd_id=LED:1040  type=NoteOn key=59 chn=1  rgb=0:15:0 lcd_pos=8:1:3 label="^std_btn"\\
 \\
-EVENT_BUTTON   id=119     hw_id=19   fwd_id=LED:6  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=3:1:3 label="R^std_btn"\\
+EVENT_BUTTON  id=1017  fwd_id=LED:1041  type=NoteOn key=68 chn=1  rgb=0:0:15 lcd_pos=1:1:4 label="^std_btn"\\
-EVENT_BUTTON   id=119     hw_id=19   fwd_id=LED:14 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=3:1:4 label="G^std_btn"\\
+EVENT_BUTTON  id=1018  fwd_id=LED:1042  type=NoteOn key=69 chn=1  rgb=0:0:15 lcd_pos=2:1:4 label="^std_btn"\\
-EVENT_BUTTON   id=119     hw_id=19   fwd_id=LED:22 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=3:1:5 label="B^std_btn"\\
+EVENT_BUTTON  id=1019  fwd_id=LED:1043  type=NoteOn key=70 chn=1  rgb=0:0:15 lcd_pos=3:1:4 label="^std_btn"\\
+EVENT_BUTTON  id=1020  fwd_id=LED:1044  type=NoteOn key=71 chn=1  rgb=0:0:15 lcd_pos=4:1:4 label="^std_btn"\\
+EVENT_BUTTON  id=1021  fwd_id=LED:1045  type=NoteOn key=72 chn=1  rgb=0:0:15 lcd_pos=5:1:4 label="^std_btn"\\
+EVENT_BUTTON  id=1022  fwd_id=LED:1046  type=NoteOn key=73 chn=1  rgb=0:0:15 lcd_pos=6:1:4 label="^std_btn"\\
+EVENT_BUTTON  id=1023  fwd_id=LED:1047  type=NoteOn key=74 chn=1  rgb=0:0:15 lcd_pos=7:1:4 label="^std_btn"\\
+EVENT_BUTTON  id=1024  fwd_id=LED:1048  type=NoteOn key=75 chn=1  rgb=0:0:15 lcd_pos=8:1:4 label="^std_btn"\\
 \\
-EVENT_BUTTON   id=120     hw_id=20   fwd_id=LED:5  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=4:1:3 label="R^std_btn"\\
+Im using my VLR-8oDisp board to show the Values of every item. You can change it to any other type of Display-setting... lcd_pos=6:1:5 {6=Display number : 1= X-axis : 5= Y-Axis (row)}
-EVENT_BUTTON   id=120     hw_id=20   fwd_id=LED:13 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=4:1:4 label="G^std_btn"\\
-EVENT_BUTTON   id=120     hw_id=20   fwd_id=LED:21 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=4:1:5 label="B^std_btn"\\
-\\
-EVENT_BUTTON   id=121     hw_id=21   fwd_id=LED:4  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=5:1:3 label="R^std_btn"\\
-EVENT_BUTTON   id=121     hw_id=21   fwd_id=LED:12 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=5:1:4 label="G^std_btn"\\
-EVENT_BUTTON   id=121     hw_id=21   fwd_id=LED:20 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=5:1:5 label="B^std_btn"\\
-\\
-EVENT_BUTTON   id=122     hw_id=22   fwd_id=LED:3  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=6:1:3 label="R^std_btn"\\
-EVENT_BUTTON   id=122     hw_id=22   fwd_id=LED:11 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=6:1:4 label="G^std_btn"\\
-EVENT_BUTTON   id=122     hw_id=22   fwd_id=LED:19 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=6:1:5 label="B^std_btn"\\
-\\
-EVENT_BUTTON   id=123     hw_id=23   fwd_id=LED:2  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=7:1:3 label="R^std_btn"\\
-EVENT_BUTTON   id=123     hw_id=23   fwd_id=LED:10 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=7:1:4 label="G^std_btn"\\
-EVENT_BUTTON   id=123     hw_id=23   fwd_id=LED:18 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=7:1:5 label="B^std_btn"\\
-\\
-EVENT_BUTTON   id=124     hw_id=24   fwd_id=LED:1  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=8:1:3 label="R^std_btn"\\
-EVENT_BUTTON   id=124     hw_id=24   fwd_id=LED:9  type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=8:1:4 label="G^std_btn"\\
-EVENT_BUTTON   id=124     hw_id=24   fwd_id=LED:17 type=cc   chn=1   cc=15   range=0:127    button_mode=OnOff lcd_pos=8:1:5 label="B^std_btn"\\
-\\
-LED_MATRIX_PATTERN n=2  pos= 0  pattern=1111110000000000\\
-LED_MATRIX_PATTERN n=2  pos= 1  pattern=0111110000000000\\
-LED_MATRIX_PATTERN n=2  pos= 2  pattern=0011110000000000\\
-LED_MATRIX_PATTERN n=2  pos= 3  pattern=0001110000000000\\
-LED_MATRIX_PATTERN n=2  pos= 4  pattern=0001110000000000\\
-LED_MATRIX_PATTERN n=2  pos= 5  pattern=0000110000000000\\
-LED_MATRIX_PATTERN n=2  pos= 6  pattern=0000010000000000\\
-LED_MATRIX_PATTERN n=2  pos= M  pattern=0000111000010000\\
-LED_MATRIX_PATTERN n=2  pos= 8  pattern=0000010000000000\\
-LED_MATRIX_PATTERN n=2  pos= 9  pattern=0000011000000000\\
-LED_MATRIX_PATTERN n=2  pos=10  pattern=0000011000000000\\
-LED_MATRIX_PATTERN n=2  pos=11  pattern=0000011100000000\\
-LED_MATRIX_PATTERN n=2  pos=12  pattern=0000011110000000\\
-LED_MATRIX_PATTERN n=2  pos=13  pattern=0000011110000000\\
-LED_MATRIX_PATTERN n=2  pos=14  pattern=0000011111000000\\
-Im using my VLR-8oDisp board to show the Values of every item. You can change it to any other type of Display-setting... lcd_pos=6:1:5 {6=Display number : 1= X-axis : 5= Y-Axis (row)}
+For any Comment or Question: Forum Thread???