Differences

This shows you the differences between two versions of the page.

--- mb-euroland [2016/08/01 15:37] – [General Design] psykhaze
+++ mb-digiroland [2016/11/12 17:06] (current) – [MIDI Use] psykhaze
@@ Line 1: / Line 1: @@
-====== MIDIbox EuRoland Project ======
+====== MIDIbox DigiRoland Project ======
-\\
-{{:neonking:euroland-logo.jpg?direct&600 |}}
 ===== Introduction =====
-The Midibox EuRoland project aims to be a **Eurorack Re-Edit of Analog Drum Parts of Roland TR Drumachines** designed to fit in the Eurorack size Format, to be driven trought MIDI or CV.
+The Midibox EuRoland project aims to be a **4U Re-Edit of Analog Drum Parts of Roland TR Drumachines** designed to fit in the Eurorack size Format, to be driven trought MIDI or CV.
 It's the Merging of these projects:
@@ Line 11: / Line 10: @@
   * [[mb-606re|MB-606RE]]
   * [[mb-808re|MB-808RE]]
-  * [[mb-909re|MB-909RE]]
 ===== Community users working on it =====
@@ Line 17: / Line 16: @@
   * **[[Phatline]]**
   * **[[Psykhaze]]**
+  * **[[Antichambre]]**
 ===== Getting Involved ? =====
@@ Line 27: / Line 26: @@
 Cases of use :\\
-  * **1. Midi:** Use the MB-Modulbox Standartmodules, for Digital UI and CV+Trig-Generation\\
+  * **1. Midi-Interface:** Use the MB-Modulbox Standartmodules, for Digital UI and CV+Trig-Generation\\
-  * **2. CV+Trig:** Just Plug CV or Trig Jacks into the Analog Modules...without Midibox.\\
+  * **2. Analog Interface:** Just Plug CV or Trig Jacks into the Analog Modules...without Midibox.\\
-==== Use with Midi ====
+===== Workshare =====
+====606====
+BD+SD > [[Psykhaze]]\\
+CY+HH > [[Phatline]]\\
+====808====
+BD, SD, TOM > [[Psykhaze]]\\
+CY, HH, COWBELL > [[Phatline]]\\
+====909====
+BD, TOM, SAMPLER-Voices > [[Psykhaze]]\\
+SD, RIM > [[Phatline]]\\
-=== MB-Modulbox Main PCB UI ===
+===== Configuration =====
+==== MIDI Use ====
+=== Main PCB UI ===
 **Access** to System-Settings, Channel, NoteNumbers\\
 **CV+Trig Out-Jacks** for Euroland Drum Modules \\
-=== MB-Modulbox 8xPotentiometer Module ===
+=== 8xPotentiometer Module ===
 When using the Euroland Modules via Midi, then there are some Performance Parameters aviable:\\
 All Functions have effect on all 8 Voices @ once.\\
-**1.Velocity Offset** (-+64 > with Center Postiton = normal)\\
+  * **1.Velocity Offset** (-+64 > with Center Postiton = normal)\\
-**2.Velocity Kill depending Note Kill** (-+64 > with Center Position = normal > Full Spectrum)\\
+  * **2.Velocity Kill depending Note Kill** (-+64 > with Center Position = normal > Full Spectrum)\\
-**3.Random Kill** (0=full Kill, 127 no Kill, Normal Position > 127)\\
+  * **3.Random Kill** (0=full Kill, 127 no Kill, Normal Position > 127)\\
-**4.Velocity 2 TriggerLength** (-+64 > with Center Position = normal 10ms, turn right:time inc by velocity in%, turn left:decrease%)\\
+  * **4.Velocity 2 TriggerLength** (-+64 > with Center Position = normal 10ms, turn right:time inc by velocity in%, turn left:decrease%)\\
-**5.Accent:** (0-127-normal 127)\\
+  * **5.Accent:** (0-127-normal 127)\\
-**6.------:** could be something like Roll\\
+  * **6.------:** could be something like Roll\\
-**7.------:** not used, could be something like a Accent for a Group of CVs\\
+  * **7.------:** not used, could be something like a Accent for a Group of CVs\\
-**8.------:** not used, could be something like a Accent for a Group of CVs\\
+  * **8.------:** not used, could be something like a Accent for a Group of CVs\\
 accessible via MB-Modulbox 8xPot - PCB. Just plug it in, and acitivate the AIN-Port in MIOS\\
@@ Line 56: / Line 68: @@
 Set CV + Trig Routing (some kind of trigger matrix), standard is 1:1 routing, so no need for this if you use a fixed setup.
-==== Use with Midi or with Analog CV+Trig ====
+==== Analog Use ====
 Here are only the Analog-Drum-PCB discussed, since all other Digital UI is based on MB-Modulbox Standart Modules, the MB-Modulbox Main PCB2 is special Variant, described here.
 ===== Software Tools used =====
@@ Line 64: / Line 77: @@
   * **[[kicad|KiCAD PCB]]** - PCB Design | **[[http://smisioto.no-ip.org/elettronica/kicad/kicad-en.htm|KiCAD Librairies]]**
   * **[[codeblocks_ide|Code::Blocks Integrated Development environment]]** - MIOS programming
-===== Eurorack Relative =====
-  * **Eurorack Design 3U Height **//=5,25"=133mm-rails=__**128,5mm**__// .
-  * **Modules Frontpanels are 8HP-multiple wide** //(8HP=__**40,3mm**__)// see //**[[http://www.doepfer.de/a100_man/a100m_e.htm|Eurorack Specification]]**//. \\ Frontpanel back spacers glued with JB-weld to avoid front screwing. **{{::neonking:eurotemplates.pdf|Eurorack Templates PDF}} | {{::neonking:eurotemplates.zip|Eurorack Templates DXF}}**\\
-   * **PCB Size is 100mm height** To stay compliant to **//[[http://www.elma.com/en/services/us-resources/eurocard-specs/|Eurocard Specification]]//**