Differences

This shows you the differences between two versions of the page.

--- coilwinder [2023/04/02 20:10] – [Shemata] phatline
+++ coilwinder [2023/04/03 23:40] (current) – phatline
@@ Line 1: / Line 1: @@
 ====== Coil Winder ======
-**REAL:**\\
+**A Tesla Coil winding machine, controlled by Mios:**\\
-{{:phatline:tm4-perspektive-l.hd-.jpg?700|}}\\
+{{phatline:Coil-Winder-Foto.jpg?900|}}\\
 \\
+Watch German Video about using it, and TimeLapse build\\
+{{youtube>z74-LL6L-BU}}\\
+\\
+Watch English Video...
+{{youtube>NtUlX4rdx-k}}\\
 ===== CODE, FIRMWARE =====
@@ Line 26: / Line 32: @@
 The Rest is stated in the youtube video, in TimeLapse\\
 You can use any motor you like, the code is programmed for a Motor that takes 400 steps for a whole 360° turn... if you use other motors you need to adapt the code (which you can download a bit above...)\\
+==== Main Parts ====
+**Midibox**:
+Core STM32 based core (STM32F4)\\
+DINX4 Module (only 3DINX are used)\\
+Levelshifter circuit from 3to5Vs (J10A to Motor-Driver)\\
+x SSD1306 Screens with 64x128 Pixels - 7Pin Variant!!!\\
+x Encoders with inbuilt switches\\
+x Momentary Button for "Play/Pause"\\
+x Breathboard ca. 100x50mm\\
+days time\\
+\\
+There are a lot of wires, nuts and screw which i have not listed here, here are only the big and expensive parts:\\
+\\
+**Amazon/Ebay/Ali...**\\
+Turner Motor:[[https://www.amazon.de/dp/B07YQQGQ4C?psc=1&ref=ppx_yo2ov_dt_b_product_details|
+Iverntech NEMA 17 Schrittmotor mit integrierter 400 mm T8-Leitspindel]] I dont think that is a good choice, the T8 Spindle bends to much... better you M10-M12 ones and 450mm or more Travel\\
+//
+Feeder Motor: [[https://www.amazon.de/dp/B07JYGRFFL?psc=1&ref=ppx_yo2ov_dt_b_product_details|Akozon Linearschiene]] - this hasent come in good condition, the first 5cm moove a bit woobly\\
+//
+Corner-Mounts: [[https://www.amazon.de/dp/B07RG9XCM2?psc=1&ref=ppx_yo2ov_dt_b_product_details|Justech 10x Winkelverbinder Aluprofil 20x20mm]] better order 2 sets...\\
+//
+x20mm Profiles: [[https://www.amazon.de/dp/B0BGKJYQ9Z?ref=ppx_yo2ov_dt_b_product_details&th=1|CNCYEAH 4 Stück 800mm Aluminiumprofil20X20 T]]\\
+//
+Stepper Motor Driver: [[https://www.amazon.de/dp/B07YWZRXGR?psc=1&ref=ppx_yo2ov_dt_b_product_details|DM542 Schrittmotor Controller]] you need 2 off them!\\
+\\
+PSU: [[https://www.amazon.de/dp/B0BVJ2RZ9B?psc=1&ref=ppx_yo2ov_dt_b_product_details|Schaltnetzteil 24V 10A ]]\\
+\\
+Mounting Kit for the Turner-Motor: [[https://www.amazon.de/dp/B07F8RLPBC?psc=1&ref=ppx_yo2ov_dt_b_product_details|42 mm Schrittmotor-Halterung]] not the stabelst one... mooves under Load...find better...\\
+\\
+Microswitches: [[https://www.amazon.de/dp/B07F9QKTQQ?psc=1&ref=ppx_yo2ov_dt_b_product_details|Mikroschalter Endschalter mit Rollenhebel 250V 5A SPDT 1NO 1NC]] you need 2 off them\\
+\\
+V-Rolls for Wires: [[https://www.amazon.de/dp/B07LF9L16L?psc=1&ref=ppx_yo2ov_dt_b_product_details|V624ZZ Kugellager V Nut Rillenkugellager]] you will need 6 off them and special M4 Screws else they will not moove\\
+\\
+T8 Nuts: [[https://www.amazon.de/dp/B086QJCX1M?psc=1&ref=ppx_yo2ov_dt_b_product_details|T8 Mutter Gewindespindel Messing Mutter]] you need 3 off them, but you may find a better way to mount your pipe on the Spindle!\\
+\\
+Flange Bearing: [[https://www.amazon.de/dp/B01MZ2M2GC?psc=1&ref=ppx_yo2ov_dt_b_product_details|Flanschlager]] you need 2 off it...\\
+===== Menue Structure =====
+Menue 1: Load and Save Coil-Data\\
+{{phatline:Coil-Winder-Menu1.jpg?600|}}\\
+//
+Menue 2: Edit Coil-Data, and get some resulting values\\
+{{phatline:Coil-Winder-Menu2.jpg?600|}}\\
+//
+Menue 3: Start the Operation, guide thru Stages\\
+{{phatline:Coil-Winder-Menu3-stage-1.jpg?600|}}\\
+{{phatline:Coil-Winder-Menu3-stage-2.jpg?600|}}\\
+{{phatline:Coil-Winder-Menu3-stage-3.jpg?600|}}\\
+{{phatline:Coil-Winder-Menu3-stage-4.jpg?600|}}\\
+{{phatline:Coil-Winder-Menu3-stage-5.jpg?600|}}\\
+{{phatline:Coil-Winder-Menu3-stage-6.jpg?600|}}\\
 ===== Community users working on it =====