aout_ng
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
aout_ng [2016/11/23 15:43] latigid_on [Connectors] |
aout_ng [2018/03/05 01:32] goyousalukis [Parts List] |
||
|---|---|---|---|
| Line 46: | Line 46: | ||
| ===== Parts List ===== | ===== Parts List ===== | ||
| \\ | \\ | ||
| - | //FIXME Add Mouser Column // | ||
| - | ^Name ^Part ^Value ^Quantity ^Reichelt Order Code ^ | + | |
| - | |**Regular Parts** ||||| | + | ^Name ^Part ^Value ^Quantity ^Reichelt Order Code ^Mouser^ |
| - | |C1,C2 |Electrolytic Capacitor |47uF |2 |RAD 105 47/35 | | + | |**Regular Parts** |||||| |
| - | |C3 |Electrolytic Capacitor |10uF |1 |RAD 105 10/63 | | + | |C1,C2 |Electrolytic Capacitor |47uF |2 |RAD 105 47/35 |140-REA470M1CBK0511P | |
| - | |C4-C10 |Capacitor |100nF |7 |Z5U-2,5 100N | | + | |C3 |Electrolytic Capacitor |10uF |1 |RAD 105 10/63 |140-RGA100M1VBK0511G | |
| - | |IC1 |D/A Converter |TLV5630 |1 |not available | | + | |C4-C10 |Capacitor |100nF |7 |Z5U-2,5 100N |594-A104K15X7RF5UAA | |
| - | |IC3,IC4 |OpAmp |TL074 |2 |TL 074 DIL | | + | |IC1 |D/A Converter |TLV5630 |1 |not available |595-TLV5630IDW | |
| - | | |Sockets for OpAmps |14-pin |2 |GS 14 | | + | |IC3,IC4 |OpAmp |TL074 |2 |TL 074 DIL |595-TL074IN | |
| - | |J1,J2 |Pin Header Single Row |none |2 |see below | | + | | |Sockets for OpAmps |14-pin |2 |GS 14 |571-1-2199298-3 | |
| - | |J3,J4 |Pin Header Single Row |none |2 |see below | | + | |J1,J2 |Pin Header Single Row |none |2 |see below |see below | |
| - | |JP1,JP2,J5 |Pin Header Dual Row |none |3 |see below | | + | |J3,J4 |Pin Header Single Row |none |2 |see below |see below | |
| - | |LED1 |LED 3 mm |none |1 |LED 3MM GN | | + | |JP1,JP2,J5 |Pin Header Dual Row |none |3 |see below |see below | |
| - | |P1-P8 |Precision Trimpot(64Y) |5k |8 |64Y-5,0k | | + | |LED1 |LED 3 mm |none |1 |LED 3MM GN | | |
| - | |R1-R8 |Metal Film Resistor 1% |27k |8 |METALL 27,0K | | + | |P1-P8 |Precision Trimpot(64Y) |5k |8 |64Y-5,0k |594-64Y502 | |
| - | |R9-R16 |Metal Film Resistor 1% |15k |8 |METALL 15,0K | | + | |R1-R8 |Metal Film Resistor 1% |27k |8 |METALL 27,0K |594-MBB02070C2702FC1| |
| - | |R49 |Resistor |470 |1 |METALL 470 | | + | |R9-R16 |Metal Film Resistor 1% |15k |8 |METALL 15,0K |594-MBB02070C1502FC1| |
| - | | |(for R49, a standard resistor can also be used) |||| | + | |R49 |Resistor |470 |1 |METALL 470 |71-CCF07470RGKE36| |
| - | |**Additional Parts for the Bipolar Option:** ||||| | + | | |(for R49, a standard resistor can also be used) ||||| |
| - | |P9-P16 |Precision Trimpot(64Y) |200 |8 |64Y-200 | | + | |**Additional Parts for the Bipolar Option:** |||||| |
| - | |R17-R32 |Metal Film Resistor 1% |10k |16 |METALL 10,0K | | + | |P9-P16 |Precision Trimpot(64Y) |200 |8 |64Y-200 |594-64Y201| |
| - | |R33-R40 |Metal Film Resistor 1% |2.2k |8 |METALL 2,20K | | + | |R17-R32 |Metal Film Resistor 1% |10k |16 |METALL 10,0K |594-MBB02070C1002FC1| |
| - | |R41-R48 |Metal Film Resistor 1% |1.5k |8 |METALL 1,50K | | + | |R33-R40 |Metal Film Resistor 1% |2.2k |8 |METALL 2,20K |594-MBB02070C2201FC1| |
| + | |R41-R48 |Metal Film Resistor 1% |1.5k |8 |METALL 1,50K |594-MBB02070C1501FC1| | ||
| **Other Parts:** | **Other Parts:** | ||
| Line 132: | Line 132: | ||
| ^ ^Core (STM/LPC)^AOUT_NG^ | ^ ^Core (STM/LPC)^AOUT_NG^ | ||
| ^Pin|//J19 (top row)//|//J1//| | ^Pin|//J19 (top row)//|//J1//| | ||
| - | ^1| Vs | Vs | | + | ^1|Vs|Vs| |
| - | ^2| Vd | Vd | | + | ^2|Vd|Vd| |
| - | ^3| SO | CS | | + | ^3|SO|CS(=RC)| |
| - | ^4| SC | SI | | + | ^4|SC|SI| |
| - | ^5| RC1 | SC | | + | ^5|RC1|SC| |
| Wire the Core end 1:1 and connect to J19. Note pin 1 is on the bottom left, on the same side as the polarising notch. Take wires 9 and 10 (red and brown in this image) and insert them between wires 4 and 5 (purple and blue in this image). Shift wires 5-8 over so 5->7, 6->8 etc. | Wire the Core end 1:1 and connect to J19. Note pin 1 is on the bottom left, on the same side as the polarising notch. Take wires 9 and 10 (red and brown in this image) and insert them between wires 4 and 5 (purple and blue in this image). Shift wires 5-8 over so 5->7, 6->8 etc. | ||
aout_ng.txt · Last modified: 2018/03/15 17:29 by goyousalukis
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
