MIDIbox

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== CV-1 ======
CV-Recorder/Looper & CV-Generator\\
Control Voltage Recorder, Looper, and Generator - for a own Eurorack-Line... more in Future!\\
{{:phatline:CV1-Case-Proto0.jpeg?500|}}\\
--this picture is the first prototype - pre-Eurorack :-D
===== Features =====
 * A Envelope which can be Recored from an AIN-Source, it can be Editet on Startpoint,ATK-Playbackrate, Decay-Playbackrate\\
 * LFO which Waveform is stepless morphable from Sine Square Tri Saw-Up to Saw-Down...(only Clocksynced!)\\
 * MSQ MotionSequencer to loop a CV-Signal.\\
 * A Mixer Page which Mixes/Mutes ENV+LFO+MSQ - and scales the output CV\\
 * Copy, Paste, Clear: to Transfair the CV Sequence to other CV1 Instances\\
 * ProgramChange Load and Store on microSD-Card, Load and Store are CC-Commands, so you can remote the device\\
 * The Sequencer can be set to Tact Systems: 3/4 4/4 5/4 7/4 9/4 11/4 13/4 

====== Hardware Requirements ======
**Midibox:**\\ 
  * [[http://wiki.midibox.org/doku.php?id=dipcoref4|dipcoref4]] - this is the µC Brain for CV1\\

  * no other PCBs needet - but expandable with other Eurorackmodules in Future\\

  * µSD-Card, formated with FAT32\\
  * Soldering Iron - with a Dip that can Handle SMD-Parts, Wires, solder Paste for the µC....\\
  * Eurorack Power Source +-12V AND +5V!\\

==== Set ====

== Cabeling ==
Midi IN1 >>> CV1 Remote Device or a Midi-Sequencer\\
Midi OUT >>> to a Global CV1 Remote Device FIXME - which will need a lot of Midiinputs [[http://wiki.midibox.org/doku.php?id=m16|M16?]]\\

  * @JMidi1: connect your Sequencer to get Midiclock and Programchanges\\ 
  * @JAIN1: 2 CV Inputs - 12V tollerant\\ 
  * @JAUT3: 1 CV Output - (internal DAC with Protection Cirtuit > 12V Tollerant)\\
  * @J19:Get up to 8 CV-Outputs, with a [[http://wiki.midibox.org/doku.php?id=aout_ng|AoutNG]]\\
  * @JLCD1: up to 4 Additional OLED-Displays for every one a Reset Line - so no additonal Circuit needet\\
  * @J89: DIN and DOUT Shiftregister Chain: thought for decidet Expander Modules (which will come in near future\\
  * @J2/Bootload: If the core is not starting up - because of bad-Firmware, then bridge this Jumper to come into the Bootload-Mode\\

====== Software ======

===== Firmware =====
yes it loopin... but not good enough to release anything...

====== Building ======
{{:phatline:CV1-PCB-3D-Front.png?500|}}\\
{{:phatline:CV1-PCB-3D-Back.png?500|}}\\


==== Frontpanel ====
FIXME - Eurorack Alu-Plate\\

==== Case ====


===== BOM =====
^Designator	^Footprint	^LCSC Part Number	^Library Type	^Mouser Part Nr
|100nF|C110|1206|C24497|basic||
|10uF|C1116,C2325|1206|C13585|basic||
|10pF|C17,C18,C19,C20,C21,C22|1206|not avaiable|||
|1N4148W|D1,D2,D3,D4,D5,D64|SOD123|C81598|basic||
|ENC|ENC1-ENC5|ENC-PEC11R|||652-PEC11R-4015F-S24|
|5x2-AOUT|J19|Header-2x5||||
|BootLoad|J2|Header-1x2||||
|DinDout|J89|Header-2x5||||
|HEADER_3|JAIN1|Header-1x3||||
|Header-1x4|JAIN2|Header-1x4-female||||
|Header-1x4|JAIN3|Header-1x4||||
|CV1|JAUT1,JAUT2|Header-1x2||||
|CV-OUT1|JAUT3|Header-1x2||||
|BiOff|JG1|Header-1x2||||
|Gain|JG2,JG3|Header-1x2||||
|Disconnect|JG4|Header-1x2||||
|Offset|JG5|Header-1x2||||
|Foot|JG6|Header-1x2||||
|Gates|JGate1|Header-2x3||||
|OLED3-6|JLCD1|Header-2x7||||
|Midi|JMidi1|Header-2x3||||
|Header-2x8-eurorack|Jpsu1|Header-2x8||||
|DIPCOREF4_52P|M1|dipCoreF4_v2c-52p-DIP-40MPNT_CORE_52P||||
|uSD_DM3ATDM3AT|M2|uSD-DM3AT-SF-PEJM5|||798-DM3AT-SF-PEJM5 |
|6N138|M3|DIP-8|||512-6N138M |
|LED-Green|Menue-1,TR1,Clock-1,ENV-1,Menue-2,TR2,ENV-2,Menue-3,Menue-4,Menue-5,Menue-6|1206-LED|C559120|extended||
|OLED|OLED1,OLED2|SSD1306:OLED-SSD1306-128x64||||
|PTC|PTC1|1206|C126818|extended||
|10K|R28,R29,R43-R58|1206|C17902|basic||
|49K9|R30-R40,R61-R64|1206|C18017|extended||
|30K|R41,R42|1206|C17999|extended||
|130K|R59|1206|C17893|extended||
|100K|R60|1206|C17900|basic||
|1K|R1-R7|1206|C4410|basic||
|4K7|R8|1206|C17936|basic||
|220|R9-R27,R63|1206|C17958|basic||
|Trim-3224W-1-104E|RV1,RV2|Trimmer-3224W-1|C53229|extended||
|Trim-3214W-1-253E|RV3|Trimmer-3214W_Vertical|||652-3214W-1-253E |
|74HC595|S1-S3|SOP-16_SOIC-16|C5947|basic||
|74HC165|S4,S5|SOP-16_SOIC-16| C5613|basic||
|TL072|U2,U3|SOP-8_SOIC-8|C6961|basic||
|MCP6002|U6|SOP-8_SOIC-8|C7377|basic||
===== To Do =====
a housing/case or frontplate\\

===== Resources =====

====== Community users working on it ======
  * **[[Phatline]]** =  Programming, Documentation...\\

Just let a Private message on the forum to user already involved.\\
I have ProtoBoards here - i test one, and if it works, i can share them for Beta Testing-if you pay the postage\\
MIDIbox

User Tools

Site Tools

Page Tools
