User Tools

Site Tools


envelope-follower-bissel-based

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
envelope-follower-bissel-based [2021/01/05 22:38]
phatline [Resources]
envelope-follower-bissel-based [2021/01/22 02:06] (current)
phatline [Envelope Follower]
Line 2: Line 2:
 based on Harry Bissel\\ based on Harry Bissel\\
 a SMD Variant, ready for Pick and Place\\ a SMD Variant, ready for Pick and Place\\
 +open-hardware,​ all Kicad-Files,​ and Gerbers are includet!\\
 {{:​phatline:​ENV-Follower-3D-rotate.png?​500|}}\\ {{:​phatline:​ENV-Follower-3D-rotate.png?​500|}}\\
 --shown 2 identical boards on one pcb - to save money.. --shown 2 identical boards on one pcb - to save money..
Line 85: Line 86:
  
 ===== To Do ===== ===== To Do =====
-experiment with the Smooting CAP, i already implimented ​Jumper which add a second ​ Capacitor ​to "​double"​ the capacity... i took 220+220nFbut maybe it is better ​to use 100+220nF?\\ +frontplate\\ 
-experiment with the Frequency Pot which is a lin10K + 2K Serial Resistor which gives a range of 2K-12K - really dont know what value spectrum we need here!\\ +Debugging First Version\\ 
-adding ​some Jumpers to break the circuit for debugging or measurement\\ +**experiment with the Smooting CAP:** Header is connected paralell ​to a integrated 100nF Capconnect there a CAP to encrease the smoothing\\ 
-frontplate, Debugging First Version\\+**experiment with the Frequency Pot:** a lin10K + 1K internal ​Serial Resistor which gives a range of 1K-12K - i also made a Header ​here, which you can bridge then you have 1-12K, or you put a resistor there for example a 5K, then you will get a range from 6-16K... ​\\ 
 +I addet some Jumpers to break the circuit for debugging or measurement\\
 \\ \\
-In order to Debug and Test and finetune the board i placed some **Headers/​Jumpers:​**\\+Modding ​**Headers/​Jumpers:​**\\
 {{:​phatline:​ENV-Follower-3D-top.png?​800|}}\\ {{:​phatline:​ENV-Follower-3D-top.png?​800|}}\\
 ===== Resources ===== ===== Resources =====
Line 99: Line 101:
 [[https://​www.muffwiggler.com/​forum/​userpix2/​10917_bom_1.jpg|THT-PCB-BOM]]\\ [[https://​www.muffwiggler.com/​forum/​userpix2/​10917_bom_1.jpg|THT-PCB-BOM]]\\
 [[https://​www.muffwiggler.com/​forum/​userpix2/​32564_scr01_2.png|Haralds-Hi-Clock-Measurements]]\\ [[https://​www.muffwiggler.com/​forum/​userpix2/​32564_scr01_2.png|Haralds-Hi-Clock-Measurements]]\\
-I give this links because it is the source: but i cant recommend that forum! (deletes of posts, shitstorm, ​not constructive posts...)+I give this links because it is the source: but i cant recommend that forum! (deletes of posts, shitstorm, ​non constructive posts...)
 ====== Community users working on it ====== ====== Community users working on it ======
   * **[[Phatline]]** =  Programming,​ Documentation...\\   * **[[Phatline]]** =  Programming,​ Documentation...\\
envelope-follower-bissel-based.1609886316.txt.gz · Last modified: 2021/01/05 22:38 by phatline