envelope-follower-bissel-based
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
envelope-follower-bissel-based [2021/01/05 22:59] phatline [To Do] |
envelope-follower-bissel-based [2021/01/22 02:06] (current) phatline [Envelope Follower] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| based on Harry Bissel\\ | based on Harry Bissel\\ | ||
| a SMD Variant, ready for Pick and Place\\ | a SMD Variant, ready for Pick and Place\\ | ||
| + | open-hardware, all Kicad-Files, and Gerbers are includet!\\ | ||
| {{:phatline:ENV-Follower-3D-rotate.png?500|}}\\ | {{:phatline:ENV-Follower-3D-rotate.png?500|}}\\ | ||
| --shown 2 identical boards on one pcb - to save money.. | --shown 2 identical boards on one pcb - to save money.. | ||
| Line 88: | Line 89: | ||
| Debugging First Version\\ | Debugging First Version\\ | ||
| **experiment with the Smooting CAP:** a Header is connected paralell to a integrated 100nF Cap, connect there a CAP to encrease the smoothing\\ | **experiment with the Smooting CAP:** a Header is connected paralell to a integrated 100nF Cap, connect there a CAP to encrease the smoothing\\ | ||
| - | experiment with the Frequency Pot which is a lin10K + 1K Serial Resistor which gives a range of 1K-12K - i also made a Header here, which you can bridge then you have 1-12K, or you put a resistor there for example a 5K, then you will get a range from 6-16K... \\ | + | **experiment with the Frequency Pot:** a lin10K + 1K internal Serial Resistor which gives a range of 1K-12K - i also made a Header here, which you can bridge then you have 1-12K, or you put a resistor there for example a 5K, then you will get a range from 6-16K... \\ |
| I addet some Jumpers to break the circuit for debugging or measurement\\ | I addet some Jumpers to break the circuit for debugging or measurement\\ | ||
| \\ | \\ | ||
| Line 100: | Line 101: | ||
| [[https://www.muffwiggler.com/forum/userpix2/10917_bom_1.jpg|THT-PCB-BOM]]\\ | [[https://www.muffwiggler.com/forum/userpix2/10917_bom_1.jpg|THT-PCB-BOM]]\\ | ||
| [[https://www.muffwiggler.com/forum/userpix2/32564_scr01_2.png|Haralds-Hi-Clock-Measurements]]\\ | [[https://www.muffwiggler.com/forum/userpix2/32564_scr01_2.png|Haralds-Hi-Clock-Measurements]]\\ | ||
| - | I give this links because it is the source: but i cant recommend that forum! (deletes of posts, shitstorm, not constructive posts...) | + | I give this links because it is the source: but i cant recommend that forum! (deletes of posts, shitstorm, non constructive posts...) |
| ====== Community users working on it ====== | ====== Community users working on it ====== | ||
| * **[[Phatline]]** = Programming, Documentation...\\ | * **[[Phatline]]** = Programming, Documentation...\\ | ||
envelope-follower-bissel-based.1609887563.txt.gz ยท Last modified: 2021/01/05 22:59 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
