MIDIbox

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=====**This page is under construction**=====


[[fadercore_-_fadermodule_for_audio_daw|Fadercore]]

Standard 220mm wide modules 

===== VLR-Motorfader =====


A solution to add up to 32 Motorfaders to your Midibox Project.
It contains 2 different Types of PCBs one is the VLR-MF_NG and the other a slim PCB to mount to your Fader so its detachable for service.



Eagle Files:



==== BOM ====
BIll of Material         

Allways look for the cheapest seller, the Price may vary heavy!!!
And look for Local dealers preferred. [[http://www.midibox.org/dokuwiki/doku.php?id=where_to_order_components]]

To make a small and easy to connect matrix over a hole Frontplatte is no fun. Thats why i made myself a better solution. Based on the common DOUT modules it can be connected to 3 SRs.

== The Materials: Mouser ==

  * 16x6pin Headers, 649-75869-131LF
  * 16x6pin Sockets, 649-71600-006LF
  * 20 Wire Ribbon Cable, 523-135-2801-020FT
  * about 80 Green LEDs, 604-WP3A8GD
  * about 80 Yellow LEDs, 604-WP3A8YD
  * about 80 Red LEDs, 604-WP3A8HD                                                                                          


Project Order Basket on Mouser: [[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=5ecf7b4949]]

The PCB is available under: 
[[https://www.vlrlab.com/home/18-ledmatrix.html]]
[[https://www.vlrlab.com/home/19-meterboard.html]]

==== How to get Started ====

The LEDs are mounted to the Edge of the Meterboard to get a very slim form. That makes it a bit harder to solder them but i guess that no one wont be able to do it. 
To solder the Header to the Edge there is a wite triangle printed to the PCB on one side. This Triange has to match with the Triangle on the Header.

==== Prepare the PCB ====
Well you should now by now how to solder Headers... :-)

==== Prepare the Connection ====

Connect the SEL, Row1-8 & Row9-16 with each a DOUT Header. 

==== Test it in MIOS ====
\\
I use a Encoder connected directly to a DIN to test.
Assuming that the DOUT is the first device on the chain of J8/9 we need to configure it like this:\\
\\
RESET_HW\\
\\
LCD "%C"\\
LCD "@(1:1:1)OLED1"\\
\\
# Test D-OUT LEDmatrix board\\
\\
DOUT_MATRIX n=1  rows=8 inverted=1 sr_dout_sel1=1 sr_dout_r1=2  sr_dout_r2=3\\
\\
# Matrix control by a Encoder connected to DIN\\
ENC n=1 sr=1 pins=0:1 type=detented2\\
\\
EVENT_ENC id= 1  fwd_id=LED_MATRIX:1   type=CC chn= 1 cc= 24  lcd_pos=1:1:2 label="^std_enc" LED_MATRIX_PATTERN=1\\
\\
LED_MATRIX_PATTERN n= 1  pos= 0  pattern=0000000000000000\\
LED_MATRIX_PATTERN n= 1  pos= 1  pattern=1000000000000000\\
LED_MATRIX_PATTERN n= 1  pos= 2  pattern=1100000000000000\\
LED_MATRIX_PATTERN n= 1  pos= 3  pattern=1110000000000000\\
LED_MATRIX_PATTERN n= 1  pos= 4  pattern=1111000000000000\\
LED_MATRIX_PATTERN n= 1  pos= 5  pattern=1111100000000000\\
LED_MATRIX_PATTERN n= 1  pos= 6  pattern=1111110000000000\\
LED_MATRIX_PATTERN n= 1  pos= 7  pattern=1111111000000000\\
LED_MATRIX_PATTERN n= 1  pos= M  pattern=1111111100000000\\
LED_MATRIX_PATTERN n= 1  pos= 8  pattern=1111111110000000\\
LED_MATRIX_PATTERN n= 1  pos= 9  pattern=1111111111000000\\
LED_MATRIX_PATTERN n= 1  pos=10  pattern=1111111111100000\\
LED_MATRIX_PATTERN n= 1  pos=11  pattern=1111111111110000\\
LED_MATRIX_PATTERN n= 1  pos=12  pattern=1111111111111000\\
LED_MATRIX_PATTERN n= 1  pos=13  pattern=1111111111111100\\
LED_MATRIX_PATTERN n= 1  pos=14  pattern=1111111111111110\\
LED_MATRIX_PATTERN n= 1  pos=15  pattern=1111111111111111\\
\\
Im using my VLR-8oDisp board to show the Values of the encoder. You can change it to any other type of Display-setting... lcd_pos=6:1:5 {6=Display number : 1= X-axis : 5= Y-Axis (row)}

For any Comment or Question: Forum Thread???
MIDIbox

User Tools

Site Tools

Page Tools
