layout_improvements
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
layout_improvements [2008/07/01 00:38] tilted |
layout_improvements [2011/11/18 16:04] (current) lpdunwell |
||
|---|---|---|---|
| Line 14: | Line 14: | ||
| * try to let ca. 5 mm free at the borders, otherwise chances are high that tracks will be damaged during splitting the boards to smaller pieces | * try to let ca. 5 mm free at the borders, otherwise chances are high that tracks will be damaged during splitting the boards to smaller pieces | ||
| * consider mounting holes at the edges | * consider mounting holes at the edges | ||
| - | * single sided boards should be prevered before double sided boards | + | * single sided boards should be preferred before double sided boards |
| * It is against the law to use any pirated/cracked software, and this is absolutely not to be done here. If you have a registered copy of Eagle, or a freeware/Eagle Light version, go right ahead. Cracked software is not only illegal, but will also corrupt the .brd files (they cannot be opened with the freeware version anymore). | * It is against the law to use any pirated/cracked software, and this is absolutely not to be done here. If you have a registered copy of Eagle, or a freeware/Eagle Light version, go right ahead. Cracked software is not only illegal, but will also corrupt the .brd files (they cannot be opened with the freeware version anymore). | ||
| * Consider Kicad if you need a larger layout. It is open source and free to download from [[http://kicad.sourceforge.net/]] | * Consider Kicad if you need a larger layout. It is open source and free to download from [[http://kicad.sourceforge.net/]] | ||
| - | * Not that a larger layout is neccesarily an improvement ;-) | + | * Not that a larger layout is neccesarily an improvement! ;-) |
| * **IMPORTANT**: never change the part numbers, they must match with the schematic to ensure consistency | * **IMPORTANT**: never change the part numbers, they must match with the schematic to ensure consistency | ||
| Line 30: | Line 30: | ||
| ^ Bridgeless MBHP_AOUT Module | NorthernLightX | [[http://home.quicknet.nl/qn/prive/alex.span/midibox/mbhp_aout_v1_bridgeless.brd]] | | | ^ Bridgeless MBHP_AOUT Module | NorthernLightX | [[http://home.quicknet.nl/qn/prive/alex.span/midibox/mbhp_aout_v1_bridgeless.brd]] | | | ||
| ^ Bridgeless MBHP_BURNER Module | NorthernLightX | [[http://home.quicknet.nl/qn/prive/alex.span/midibox/mbhp_burner_v1_bridgeless.brd]] | | | ^ Bridgeless MBHP_BURNER Module | NorthernLightX | [[http://home.quicknet.nl/qn/prive/alex.span/midibox/mbhp_burner_v1_bridgeless.brd]] | | | ||
| - | ^ Some Layouts (including core) | rdoursenaud | [[http://rdoursenaud.free.fr/midibox/]] | | | + | ^ Some Layouts (including core) | rdoursenaud | [[http://raphael.doursenaud.fr/category/midibox/]] | | |
| - | ^ Improved MBHP_OPL3 Module | [[selfservice]] | [[http://www.cronokart.com/midibox/MBHP_OPL3FM_V1_SCH.pdf]] | Take care about the CORE->OPL3 connections, some pins are swapped | | + | ^ Improved MBHP_OPL3 Module | [[selfservice]] | [[http://www.splabs.it/?p=16]] | Take care about the CORE->OPL3 connections, some pins are swapped | |
| - | ^ "" | "" | [[http://www.cronokart.com/midibox/MBHP_OPL3FM_V1_BOT_V2.pdf]] | This is the bottom layer | | + | ^ "" | "" | [[http://www.splabs.it/?p=16]] | This is the bottom layer | |
| - | ^ "" | "" | [[http://www.cronokart.com/midibox/MBHP_OPL3FM_V1_AST_V2.pdf]] | This is the assembly top | | + | ^ "" | "" | [[http://www.splabs.it/?p=16]] | This is the assembly top | |
| ====== Ideas ====== | ====== Ideas ====== | ||
layout_improvements.1214872712.txt.gz · Last modified: 2008/07/01 00:38 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
