mb-sidr8tr
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Last revision Both sides next revision | ||
|
mb-sidr8tr [2011/01/24 05:24] m00dawg Added Power board |
mb-sidr8tr [2011/01/24 14:01] m00dawg |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== MB-SIDR8TR ====== | + | Moved to [[mb-sidr8tr:start]] |
| - | + | ||
| - | This is a project built around making a MidiBox SID in a 3U rackmount case using the MB-6582 mainboard. This is a **huge** work in progress however feel free to contribute! | + | |
| - | + | ||
| - | ===== Parts ===== | + | |
| - | + | ||
| - | * [[http://www.jameco.com/webapp/wcs/stores/servlet/ProductDisplay?langId=-1&productId=132848&catalogId=10001&storeId=10001|3U Chassis]] - Jameco Part # 132848 | + | |
| - | + | ||
| - | ===== Panels ===== | + | |
| - | + | ||
| - | This is the current iteration of the panel. It is not final and, in fact, you can likely see a few mistakes here and there. | + | |
| - | + | ||
| - | {{:mb6582r.zip|}} | + | |
| - | + | ||
| - | ===== Boards ===== | + | |
| - | + | ||
| - | Here are the collection of boards required to populate the control surface. Since a single-board solution would be quite expensive (starting with the full version of EagleCAD), the design is more similar to the standard C64-based control surface in that various parts of the control surface can be populated using smaller boards. | + | |
| - | + | ||
| - | That said, since the MB-6582R uses the MB-6582 mainboard, the wiring reflects the use of LED and button arrays. The wiring can be found here at the following: | + | |
| - | + | ||
| - | * {{mb-6582:mb-6582_cs_dout_wiring.pdf}} | + | |
| - | + | ||
| - | * {{mb-6582:mb-6582_cs_din_wiring.pdf}} | + | |
| - | + | ||
| - | Further details can be found on the MB-6582 [[wilba_mb_6582|wiki]] page. | + | |
| - | + | ||
| - | ==== LED Matrix ==== | + | |
| - | + | ||
| - | This is a proposed layout for an LED matrix board to be used coupled with the above panel design. While other boards can likely be made from home using various methods, it might be wise to have this one printed. Note that this design currently has the mounting holes up higher than the current design of the front panel. The mounting holes were moved down on the panel so the design was more uniform. Modify per your needs! | + | |
| - | + | ||
| - | {{:mb6582r-led-matrix-board.png?320}} | + | |
| - | {{:mb6582r-led-matrix-schematic.png?320}} | + | |
| - | {{:mb-6582r-led-matrix-eagle.zip|Eagle}} | + | |
| - | + | ||
| - | ==== Power ==== | + | |
| - | + | ||
| - | The power board supplies +/- 12V, +9V and +5V. +12V might be able to be used for a SID-6581 but the board is really optimized around suppling +9V (in other words, 8580/6852 SIDs). This board is based off [[northernlightx]]'s Complete PSU with a few modifications. The +/- 12V is for adding AOUT modules (namely for [[http://www.midibox.org/dokuwiki/doku.php?id=ssm2044_pcb|SSM 2044]] filters). | + | |
| - | + | ||
| - | {{:sidr8tr-power-board.png?320}} | + | |
| - | {{:sidr8tr-power-sch.png?320}} | + | |
| - | {{:sidr8tr-power.zip|}} | + | |
| - | + | ||
| - | ===== Props ===== | + | |
| - | + | ||
| - | Thanks to TK, Wilba, SmashTV, and nILS for their help, inventions, and support. Without them, this would not have been possible! | + | |
mb-sidr8tr.txt · Last modified: 2011/01/24 14:01 by m00dawg
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
