parts_faq
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
parts_faq [2016/06/15 12:42] psykhaze [What kind of switches do I need?] |
parts_faq [2016/06/15 12:47] (current) psykhaze [What is the correct polarity of the (resistor / capacitor / diode / etc)] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Parts FAQ (Frequently Asked Questions) ====== | ====== Parts FAQ (Frequently Asked Questions) ====== | ||
| \\ | \\ | ||
| - | \\ | + | {{ ::neonking:partsfaq.jpg?direct&400|}} |
| ===== What wattage resistors should I buy? ===== | ===== What wattage resistors should I buy? ===== | ||
| Line 16: | Line 17: | ||
| **Resistors can be installed in any direction**. | **Resistors can be installed in any direction**. | ||
| - | Smaller value capacitors (i.e. usually under 1 uF) generally have no polarity. Anything above 1 uF is typically an electrolytic capacitor, and it will have a polarity marking. Most often the "-" side is marked with a big stripe, although sometimes it's the "+" side that is marked. (Strangely, the "+" side seems to be marked on capacitors made in U.S.A.) | + | **Smaller value capacitors (i.e. usually under 1 uF) generally have no polarity**. **Anything above 1 uF is typically an electrolytic capacitor, and it will have a polarity marking**. Most often the "-" side is marked with a big stripe, although sometimes it's the "+" side that is marked. (Strangely, the "+" side seems to be marked on capacitors made in U.S.A.) |
| **//Diodes absolutely must be installed in the right direction//**. Diodes have a stripe on the cathode side. | **//Diodes absolutely must be installed in the right direction//**. Diodes have a stripe on the cathode side. | ||
| Line 67: | Line 68: | ||
| Trying to save money on wobbly cheap plastic faders, uh? You might hate yourself for that decision after six months of using your favorite new midi-toy. Consider that. | Trying to save money on wobbly cheap plastic faders, uh? You might hate yourself for that decision after six months of using your favorite new midi-toy. Consider that. | ||
| + | \\ | ||
| + | \\ | ||
| ===== What type of crystal do I need? ===== | ===== What type of crystal do I need? ===== | ||
| Line 73: | Line 75: | ||
| [[Crystals and Oscillators]] | [[Crystals and Oscillators]] | ||
| + | \\ | ||
| + | \\ | ||
| ===== I can't find a bridge rectifier to fit the PCB's. ===== | ===== I can't find a bridge rectifier to fit the PCB's. ===== | ||
| You can substitute four 1N4001 (or any of the 1N400X series) for the bridge rectifier, they will handle more than enough current. | You can substitute four 1N4001 (or any of the 1N400X series) for the bridge rectifier, they will handle more than enough current. | ||
| + | \\ | ||
| + | \\ | ||
| ===== What Power supply should I use, and how much power should it have? ===== | ===== What Power supply should I use, and how much power should it have? ===== | ||
| Line 101: | Line 105: | ||
| Yes, 1N4004 is a replacement for 1N4002, it's just a type for higher Voltages (100V for 1N4002 vs. 400V for 1N4004). Any 1N400X diode will work in place of any other 1N400X diode -WITH A SMALLER NUMBER- Do replace a 1N4002 with a 1N4004 Don't replace a 1N4004 with a 1N4002 | Yes, 1N4004 is a replacement for 1N4002, it's just a type for higher Voltages (100V for 1N4002 vs. 400V for 1N4004). Any 1N400X diode will work in place of any other 1N400X diode -WITH A SMALLER NUMBER- Do replace a 1N4002 with a 1N4004 Don't replace a 1N4004 with a 1N4002 | ||
| + | \\ | ||
| + | \\ | ||
| ===== PIC Stuff ===== | ===== PIC Stuff ===== | ||
parts_faq.1465994562.txt.gz · Last modified: 2016/06/15 12:42 by psykhaze
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
