MIDIbox

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
\\

Because the information in the SpeakJet Manual is relatively wide spreaded, this page gives a quick overview of the control possibilities of the Speakjet:

\\
====== MSA (Mathmatical Sound Architecture) ======
MSA commands are stored in the 64-Byte input buffer and are executed in the order they are received.

===== MSA Controls =====
An 'X' indicates that a second number should follow as parameter.

==== Pause Control ====
000: Pause 0 ms\\
001: Pause 100 ms\\
002: Pause 200 ms\\
003: Pause 700 ms\\

004: Pause 30 ms\\
005: Pause 60 ms\\
006: Pause 90 ms\\

016: Wait // Watch out! Waits for event input line or SCP-Start command!//\\
030: Delay, X // number of 10 ms intervals to delay before continuing on to the next code, accepts 0-255//\\

==== Next Sound Control ====
007: Play next sound fast\\
008: Play next sound slow\\

014: Play next sound high\\
015: Play next sound low\\

==== Volume/Pitch/Speed/Bend Control ====
020: Volume, X // sets Master Volume Level, accepts 0-127//\\
021: Speed, X // Play Speed, default 114, accepts 0-127//\\
022: Pitch, X // Pitch in Hertz, only for voiced sounds, default 88, accepts 0-255 (=32kHz..240kHz)//\\
023: Bend, X // Sets the Frequency Band (from deep hollow to high metallic), default 5, accepts 0-15//\\

==== Port Control ====
024: PortCtr, X // binaurally encoded output line control, see manual for details, default 7, accepts 0-7//\\
025: Port, X // port output value, see manual for details, default 0, accepts 0-7//\\

==== Phrase Control ====
026: Repeat, X // repeats the next code x-times, accepts 0-255//\\
028: Call Phrase, X // which EEPROM phrase to play, max 3 level deep nesting//\\
029: Goto Phrase, X // which EEPROM phrase to play//\\
255: End of Phrase

==== Reset ====
031: Reset Defaults

\\
===== MSA Sound Codes =====
128..254: MSA Sound Phrases and Effects, see [[SpeakJet Definition List]].


\\
\\
====== SCP (Serial Control Protocol) ======
SCP commands are executed immediately and provide control over the 5-channel synthesizer as well as accessing the internal speakjet EEPROM.

\\
===== Entering SCP =====
'\0' to enter SCP

==== SCP Commands ====
'H': Store Memory Type //accepts 0 and 32//\\
  * '0H': Write a register's value\\
  * '32H': Write to the internal EEPROM\\
'J': Memory Address\\
  * '0J': Envelope Freq\\
  * '1J': OSC1 Freq .. '5J': OSC5 Freq\\
  * '6J': Distortion\\
  * '7J': Master Volume\\
  * '8J': Envelope Control\\
  * '11J': OSC1 Vol .. '15J': OSC5 Vol\\
'N': Store Memory\\
'R': Clear Buffer\\
'S': Stop Enounciating\\
'T': Start Enounciating\\
'V': ACK\\
'W': Hard Reset\\

\\
===== Exiting SCP =====
'X' or '\A'\\

\\
===== Examples =====

\0 V X*\\
//Enters SCP-Mode, enounciates READY and exits SCP-mode//

8J 0N 1J 500N 11J 16N*\\
//1st OSC freq 500 and vol 16//

0J 32H 01N*\\
//write 0x1 to the first location of internal EEPROM//

8J 00N*\\
//set env-type to SAW//

8J 10N*\\
//set env-type to TRIANGLE//

//* Don't send spaces, this is just for readability!//
MIDIbox

User Tools

Site Tools

Page Tools
