MIDIbox

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
======SELEKTOR II======

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20MB%202%203/DSC00552.gif| }} \\

This is Wild_Weasel little Midibox Traktor section.This is again a denon remote control unit retrofit, namely a RC-35 MK III for the DENON DN-2000F MK III cd-player unit.

The unit was bought at ebay for approximately 50€.
After testing the player, which still worked, I ripped it apart. 

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00275.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00276.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00277.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00278.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00279.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00280.jpg}}

After that I desoldered the PCB to have a template for making new ones. This was done with the help of a desoldering pump.
The pushbuttons, the leds and the jog/shuttle wheel have been desoldered.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00285.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00286.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00287.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00288.jpg}}

Cutting the new PCB using a small cutter for my dremel tool. Two boars are done, one for the left and the right side of the unit.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00290.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00291.jpg}}

Drilling the new PCB using the old PCB as template. Doing so you achieve a perfect fit of your PCB into the unit.
Don't forget to drill the mounting holes too. I am using clamps to keep the two boards aligned during the process


{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00292.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00293.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00294.jpg}}

Afterwards I milled new soldering pads using my dremel tool again. One pin from each pushbutton is insulated from the rest of the board (which acts as ground) this way.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00295.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00296.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00297.jpg}}

Mounting the parts and attaching cables.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00298.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00299.jpg}}

A DIN X4 is piggybacked to each board with M3 srews and spacers.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00300.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00301.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00302.jpg}}

First test with a core modul attached.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00303.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/DSC00306.jpg}}

**Update 23.9.2006**

Scuffing the silkscreening away

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%201/DSC00307.jpg}}
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%201/DSC00309.jpg}}\\
{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%201/DSC00314.gif}}

DOUT module installed. Even works with high power blue and white LEDs.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%201/DSC00311.jpg}}

Position of future encoderes for FX section.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%201/DSC00312.jpg}}

**Update 26.9.2006**

Welding and soldering additional sheet metal to cover the display cutouts.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%202/DSC00315.jpg}}

Partly finished after bondoing and sanding.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202%202/DSC00319.jpg}}

**Update 13.2.2007**

I added 8 Encoders for FX controll. Turning left/right increases/decreases the value. Pushing the Encodes activates/ deactivates the FX-Button in Traktor. Pushing the outermost encoder with the shift-button engaged changes the selected FX in Traktor.

{{http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20MB%202%203/DSC00552.gif}} \\
----

=====Code area=====
Note: This code is not finished

- V1.0 \\
http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20mb%202/Selektor%20II%20v1.0.rar\\ 
\\
- V1.5 \\

  * added shuttle ring support \\ 
  * added FX Knob controll \\

http://stud3.tuwien.ac.at/~e0327352/midibox/denon%20MB%202%203/SELEKTORIIV15.rar \\ 
\\
----


=====Still to come:=====

<del>FX-Encoder</del>\\
finished C Code\\
<del>USB connection\\</del> Midi I/O included in the Traktor Scratch Interface, therfore no usb will be used\\
Painting\\
labeling [self-adhesive, clear, laserprinter-sheets will be used]
MIDIbox

User Tools

Site Tools

Page Tools
