fadercore_-_vlr-motorfader
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
fadercore_-_vlr-motorfader [2014/07/30 10:59] – novski | fadercore_-_vlr-motorfader [2014/11/10 20:22] (current) – novski | ||
---|---|---|---|
Line 12: | Line 12: | ||
It contains 2 different Types of PCBs one is the VLR-MF_NG and the other a slim PCB to mount to your Fader so its detachable for service. | It contains 2 different Types of PCBs one is the VLR-MF_NG and the other a slim PCB to mount to your Fader so its detachable for service. | ||
- | {{: | ||
- | Eagle Files: [[https:// | ||
- | {{:fadercore_vlr-ledmatrix_unbestueckt_top.png? | + | Eagle Files: |
- | {{: | + | |
==== BOM ==== | ==== BOM ==== | ||
Line 25: | Line 24: | ||
And look for Local dealers preferred. [[http:// | And look for Local dealers preferred. [[http:// | ||
- | To make a small and easy to connect matrix over a hole Frontplatte is no fun. Thats why i made myself a better solution. Based on the common DOUT modules it can be connected to 3 SRs. | ||
== The Materials: Mouser == | == The Materials: Mouser == | ||
- | * 3x10pin Header, 517-30310-6002 | + | * |
- | * 6x10pin | + | * 8x6pin |
- | * 16x20pin Header, 517-30320-6002 | + | * |
- | * 16x20pin Sockets, 517-D89120-0131HK | + | * 1 Green LED, 604-WP3A8GD |
- | * 20 Wire Ribbon Cable, 523-135-2801-020FT | + | * |
- | * about 80 Green LEDs, 604-WP3A8GD | + | |
- | * about 80 Yellow LEDs, 604-WP3A8YD | + | |
- | * about 80 Red LEDs, 604-WP3A8HD | + | |
- | Project Order Basket on Mouser: [[http:// | + | Project Order Basket on Mouser: [[http:// |
The PCB is available under: | The PCB is available under: | ||
- | [[https:// | + | [[https:// |
- | [[https:// | + | [[https:// |
==== How to get Started ==== | ==== How to get Started ==== | ||
- | The LEDs are mounted to the Edge of the Meterboard to get a very slim form. That makes it a bit harder to solder them but i guess that no one wont be able to do it. | + | |
- | To solder the Header to the Edge there is a wite triangle printed to the PCB on one side. This Triange has to match with the Triangle on the Header. | + | |
==== Prepare the PCB ==== | ==== Prepare the PCB ==== | ||
- | Well you should now by now how to solder Headers... :-) | + | |
==== Prepare the Connection ==== | ==== Prepare the Connection ==== | ||
- | Connect the SEL, Row1-8 & Row9-16 with each a DOUT Header. | + | |
==== Test it in MIOS ==== | ==== Test it in MIOS ==== | ||
\\ | \\ | ||
- | I use a Encoder connected directly to a DIN to test. | + | |
- | Assuming that the DOUT is the first device on the chain of J8/9 we need to configure it like this:\\ | + | |
- | \\ | + | |
- | RESET_HW\\ | + | |
- | \\ | + | |
- | LCD " | + | |
- | LCD " | + | |
- | \\ | + | |
- | # Test D-OUT LEDmatrix board\\ | + | |
- | \\ | + | |
- | DOUT_MATRIX n=1 rows=8 inverted=1 sr_dout_sel1=1 sr_dout_r1=2 | + | |
- | \\ | + | |
- | # Matrix control by a Encoder connected to DIN\\ | + | |
- | ENC n=1 sr=1 pins=0:1 type=detented2\\ | + | |
- | \\ | + | |
- | EVENT_ENC id= 1 fwd_id=LED_MATRIX: | + | |
- | \\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 0 pattern=0000000000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 1 pattern=1000000000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 2 pattern=1100000000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 3 pattern=1110000000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 4 pattern=1111000000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 5 pattern=1111100000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 6 pattern=1111110000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 7 pattern=1111111000000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= M pattern=1111111100000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 8 pattern=1111111110000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos= 9 pattern=1111111111000000\\ | + | |
- | LED_MATRIX_PATTERN n= 1 pos=10 | + | |
- | LED_MATRIX_PATTERN n= 1 pos=11 | + | |
- | LED_MATRIX_PATTERN n= 1 pos=12 | + | |
- | LED_MATRIX_PATTERN n= 1 pos=13 | + | |
- | LED_MATRIX_PATTERN n= 1 pos=14 | + | |
- | LED_MATRIX_PATTERN n= 1 pos=15 | + | |
- | \\ | + | |
- | Im using my VLR-8oDisp board to show the Values of the encoder. You can change it to any other type of Display-setting... lcd_pos=6: | + | |
For any Comment or Question: Forum Thread??? | For any Comment or Question: Forum Thread??? |
fadercore_-_vlr-motorfader.1406717994.txt.gz · Last modified: 2014/07/30 10:59 by novski