Differences

This shows you the differences between two versions of the page.

--- how_to_use_midibox_cv_with_a_dout [2006/03/27 13:21] – talion
+++ how_to_use_midibox_cv_with_a_dout [2009/05/06 14:23] (current) – 129.120.95.63
@@ Line 1: / Line 1: @@
-Midibox CV um dout's erweitern
+**Midibox CV to extend "DOUTs"**
-Wem zwei bzw. acht Gates zu wenig sind, oder Vintage Drummer (Roland x0x) Triggern will, wird schnell feststellen, dass er mit der
+Anyone who considers 2 or 8 gates too few, or wants to trigger vintage drum synths/modules (Roland x0x style), may find the existing hardware of the Midibox CV insufficient. The solution is simple.
-vorhandenen Hardwareausstattung der Midibox CV nicht auskommt. Die Lösung ist denkbar einfach und wird im Folgenden
-erläutert.
-Hardwareseitig -
+**Hardware**
-wird ein dout Modul benötigt, welches mit J8 des Coremodules verbunden wird. Ein doutx4 stellt 32 Gates/Trigger bereit. An dieser
-Stelle der Hinweis: Da hier ohne Optokopller oder Transistoren gearbeitet wird, unbedingt darauf achten das die Gates/Trigger nicht
-"belastet" oder gar kurz geschlossen werden.
-Softwareseitig -
+A dout module is needed, which will be connected to J8 of the coremodule. A doutx4 provides 32 gates/triggers.
-sind einige Änderungen am Code zu machen. Zum einen muss das dout bei einem NoteOn der entsprechenden Note den Gate/Trigger
+Some advice at this point: because it will be built without any optocouplers or transistors to protect the DOUT, it is essential not to apply any external voltage to the Gates/Triggers, and also to prevent short circuit.
-aktivieren, zum anderen kann man optional die Dauer des Impulses, unabhängig der Länge der Note, auf 1ms reduzieren. Hintergrund
-ist die eigenart mancher Drummer. So lösen die x0x-Boxen (606, 808, 909 ...) den Sound nicht bei Anschwellen der Gatespannung, sondern
-beim wieder Abflachen aus.
-DOUT AKTIVIEREN:
+**Software**
-Sourcen von Midibox CV herunterladen [[http://http://www.ucapps.de/mios_download.html|http://www.ucapps.de/mios_download.html]] und in main.asm nach dieser Stelle suchen:
+A few changes have to be made to the sourcecode. On the one hand, the dout has to activate the gate/trigger on receiving the appropriate NoteOn: on the other hand you may want to reduce the duration of an impulse to 1ms
+independent of the Note duration.
+Here as background is the trigger characteristic of some drum machines. The x0x-boxes (606,808,909...) trigger the sound at decrease of voltage at the gate instead of increase.\\  //IE at the trailing edge of the +ve pulse rather than the leading edge? I'm not sure if this is correct.\\  [[http://en.wikipedia.org/wiki/CV/Gate#Gate|Wikipedia]] says that Roland and Sequential gear is V-Trig {normal low, set high to trigger} and Moog, Korg and Yamaha is S-Trig {normal high, set low to trigger}.  The [[http://66.102.7.104/search?q=cache:IBefydaCrJIJ:www.kentonuk.com/kmanualspdf/psoloman.pdf+%22V-trig%22+edge&hl=en&gl=au&ct=clnk&cd=5&client=firefox|manual]] for the Kenton Pro Solo MIDI-CV converter says: " ... Most synths / sequencers & drum machines will want the Positive edge pulse, but a few require the Negative edge instead. (e.g. Korg Monopoly) .. " I've also seen written elsewhere that the 606 trigger out is V-Trig, but the 707 internal triggering for it's own voices is S-Trig\\ Also, if the trailing edge was the trigger, how would gates and envelopes work ie ADSR when AD happens at leading edge, D as gate is held high, and R when gate drops low? - Bunsen//
+__Activate dout:__
+Download the source of Midibox CV at http://www.ucapps.de/mios_download.html and search for the following in
+"main.asm":
+<code>
 USER_MPROC_NotifyReceivedEvent
 	;; process MIDI event
@@ Line 27: / Line 27: @@
 	;; will be mapped immediately
 	rgoto	USER_Tick
+</code>
-Mit diesem Code ersetzen:
+Replace it with:
+<code>
 USER_MPROC_NotifyReceivedEvent
+	;; BEGIN --- control DOUT pins via Note events at channel #1
+	movf	MIOS_PARAMETER1, W		; Note Off -> Note On with velocity 0
+	andlw	0xf0
+	xorlw	0x80
+	bnz	USER_MPROC_NRE_NoNoteOff
+USER_MPROC_NRE_NoteOff
+	bsf	MIOS_PARAMETER1, 4
+	clrf	MIOS_PARAMETER3
+USER_MPROC_NRE_NoNoteOff
 	movlw	0x90				; check for Note On at channel #1
-	IFNEQ	MIOS_PARAMETER1, ACCESS, rgoto USER_MPROC_NRE_NoNoteChn1
+	cpfseq MIOS_PARAMETER1, ACCESS
+	rgoto USER_MPROC_NRE_NoNoteChn1
 USER_MPROC_NRE_NoteChn1
 	;; MIOS_DOUT_PinSet expects pin number in WREG, value in MIOS_PARAMETER1
@@ Line 54: / Line 66: @@
 	;; will be mapped immediately
 	rgoto	USER_Tick
+</code>
+What happens here? Midibox CV is listening to the first channel (beginning from tune C-2) for a NoteOn and
+activates the corresponding dout. A NoteOff deactivates the dout.
+__Define the number of connected DOUT shift registers:__
-Was passiert hier? Midibox CV lauscht nun auf dem ersten Channel ab der Note C-2 auf einen NoteOn und aktiviert bei gespielter Note
+If you're using more than one DOUT shift register, you must also change this code in "main.inc" to reflect the number of shift registers:
-den entsprechenden dout. Bei einem NoteOff wird dieser wieder abgeschaltet.
+<code>
+	;; initialize the SRIO driver
+	movlw	0x01
+	call	MIOS_SRIO_NumberSet
+</code>
+To set it to the maximum (16), just replace the code with this:
+<code>
+	;; initialize the SRIO driver
+	movlw	0x0F
+	call	MIOS_SRIO_NumberSet
+</code>
-MS ERWEITERUNG FÜR VINTAGE DRUMMER:
-Wer Vintage Drummer triggern will muss diesen Code zusätzlich in die main.asm einsetzen. Nach folgender Stelle suchen:
+__1ms Extension For Vintage Drum Machines:__
+Those who want to trigger vintage drums have to modify the sourcecode as follows:
+Search for the following:
+<code>
 USER_SR_Service_Finish
 	;; ---[ handle with control surface variables (flashing cursor, etc) ]---
 	goto	CS_MENU_TIMER
+</code>
+Replace it with:
-Und mit diesem Code ersetzen:
+<code>
 USER_SR_Service_Finish
 	clrf    MIOS_PARAMETER1
 	movlw   0x00
 	call    MIOS_DOUT_SRSet
@@ Line 81: / Line 109: @@
 	call    MIOS_DOUT_SRSet
 	movlw   0x03
 	call    MIOS_DOUT_SRSet
 	;; ---[ handle with control surface variables (flashing cursor, etc) ]---
 	goto	CS_MENU_TIMER
+</code>
+This leads to a reset of all DOUTs once per cycle - this lasts 1ms. So the drum modules can be triggered
+with a 1ms latency.
+MIDIbox SEQ allows up to 48 digital outputs as this type of trigger. [[http://ucapps.de/midibox_seq_options.html]]
+__Changing the midi channel:__
-Hiermit erreicht man, dass bei jedem Cycle die dout's zurückgesetzt werden - das dauert 1ms. Somit kann man die Drummodule mit 1ms Latenz
+If you want the DOUT triggers to respond to MIDI events on a channel other than #1, replace instances of "0x80" and "0x90" with the following values:
-triggern.
+  * Channel 1: 0x80, 0x90
+  * Channel 2: 0x81, 0x91
+  * Channel 3: 0x82, 0x92
+  * Channel 4: 0x83, 0x93
+  * Channel 5: 0x84, 0x94
+  * Channel 6: 0x85, 0x95
+  * Channel 7: 0x86, 0x96
+  * Channel 8: 0x87, 0x97
+  * Channel 9: 0x88, 0x98
+  * Channel 10: 0x89, 0x99
+  * Channel 11: 0x8A, 0x9A
+  * Channel 12: 0x8B, 0x9B
+  * Channel 13: 0x8C, 0x9C
+  * Channel 14: 0x8D, 0x9D
+  * Channel 15: 0x8E, 0x9E
+  * Channel 16: 0x8F, 0x9F
+__Forum articles:__
-Themen im Forum:
+[[http://www.midibox.org/forum/index.php/topic,13478.0.html]] -- Information on receiving on ALL channels, information on excluding specific DOUT pins from being reset with the 1ms trigger extension code
-[[http://http://www.midibox.org/forum/index.php?topic=2701.0|http://www.midibox.org/forum/index.php?topic=2701.0]]
+[[http://www.midibox.org/forum/index.php?topic=2701.0]] (German)\\
-[[http://http://www.midibox.org/forum/index.php?topic=6333.0|http://www.midibox.org/forum/index.php?topic=6333.0]]
+[[http://www.midibox.org/forum/index.php?topic=6333.0]] (German)