This shows you the differences between two versions of the page.
— |
scs-oled [2018/03/06 21:09] (current) latigid_on created |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== SCS OLED module ====== | ||
+ | |||
+ | Combination of 0.96" SSD1306 OLEDs and switches for an [[http://www.ucapps.de/midibox_ng_manual_scs.html|SCS]] | ||
+ | |||
+ | ===== Schematic ===== | ||
+ | |||
+ | Refer to the SCS schematic or below for J1/button and encoder pinning and the Core module (J15) for J5/OLEDs. | ||
+ | |||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | ===== BOM v1.0 ===== | ||
+ | |||
+ | ^ Type ^ Part ^ Value ^ | ||
+ | |Caps | C25 | DNF | | ||
+ | | | C26 | DNF | | ||
+ | | | C29 | 10uF polarised | | ||
+ | |Encoder | EN1 | 12mm | | ||
+ | | | EN2 | 12mm | | ||
+ | |Header | J1 | PINHD-2X54WALL | | ||
+ | | | J2 | +5V | | ||
+ | | | J5 | PINHD-2X54WALL | | ||
+ | |OLEDs | LCD1 | 0.96_OLED | | ||
+ | | | LCD2 | 0.96_OLED | | ||
+ | | | LCD3 | 0.96_OLED | | ||
+ | | | LCD4 | 0.96_OLED | | ||
+ | |Resistors | R3 | DNF | | ||
+ | | | R4 | DNF | | ||
+ | | | R7 | DNF | | ||
+ | | | R9 | 2k2 | | ||
+ | |Switches | S1(A) | DT6 or 6mm | | ||
+ | | | S2(A) | DT6 or 6mm | | ||
+ | | | S3(A) | DT6 or 6mm | | ||
+ | | | S4(A) | DT6 or 6mm | | ||
+ | | | S5(A) | DT6 or 6mm | | ||
+ | | | S6(A) | DT6 or 6mm | | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Versions ===== | ||
+ | v1.0: first release | ||
+ | |||
+ | ===== Assembly ===== | ||
+ | |||
+ | Decide on the configuration to be used. Any combination of switches, encoders or OLEDs is possible if they fit. | ||
+ | |||
+ | Only one encoder is wired to the J1 header. If you want to use the EN2 position, wire the legs to the empty EN1 solder points. | ||
+ | |||
+ | R9 and C29 form the power-on reset for OLEDs. R7 should not be installed. R3/C25/R4/C26 form a termination shunt for OLED data lines. They shouldn't be required. | ||
+ | |||
+ | The switches accommodate either DT6 or 6mm switches (obviously only one type!). For DT6 switches, ensure the flat side is aligned with the PCB silkscreen. | ||
+ | |||
+ | J2 can supply power if needed. | ||
+ | |||
+ | |||
+ | |||
+ | ==== Interconnections ==== | ||
+ | |||
+ | {{::scsoled:j1.png?nolink&200|}} | ||
+ | |||
+ | J1 is the SCS header, connecting to J10A | ||
+ | |||
+ | J2 can provide power as indicated; it is also connected on J5. | ||
+ | |||
+ | J5 connects to J15 on the Core (or equivalent) | ||
+ | |||
+ | ===== Dimensions ===== | ||
+ | |||
+ | {{:scsoled:scsoled.png?link&600|}} | ||
+ | |||
+ | {{ :scsoled:doku.zip |}} | ||
+ | ===== License ===== | ||
+ | |||
+ | Currently the design is (c) 2016 antilog devices with all rights reserved; all documentation is CC BY-NC-SA 3.0. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||