speakjet_control_overview
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
speakjet_control_overview [2006/06/11 14:05] audiocommander created |
speakjet_control_overview [2006/12/05 14:03] (current) audiocommander Removed progress-note, document is up-to-date. |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| \\ | \\ | ||
| - | :!: **THIS DOCUMENT IS CURRENTLY UNDER CONSTRUCTION** :!: | + | |
| - | \\ | + | Because the information in the SpeakJet Manual is relatively wide spreaded, this page gives a quick overview of the control possibilities of the Speakjet: |
| \\ | \\ | ||
| ====== MSA (Mathmatical Sound Architecture) ====== | ====== MSA (Mathmatical Sound Architecture) ====== | ||
| - | |||
| MSA commands are stored in the 64-Byte input buffer and are executed in the order they are received. | MSA commands are stored in the 64-Byte input buffer and are executed in the order they are received. | ||
| ===== MSA Controls ===== | ===== MSA Controls ===== | ||
| + | An 'X' indicates that a second number should follow as parameter. | ||
| - | ==== Pause ==== | + | ==== Pause Control ==== |
| 000: Pause 0 ms\\ | 000: Pause 0 ms\\ | ||
| 001: Pause 100 ms\\ | 001: Pause 100 ms\\ | ||
| Line 20: | Line 20: | ||
| 006: Pause 90 ms\\ | 006: Pause 90 ms\\ | ||
| - | 016: Wait\\ | + | 016: Wait // Watch out! Waits for event input line or SCP-Start command!//\\ |
| - | + | 030: Delay, X // number of 10 ms intervals to delay before continuing on to the next code, accepts 0-255//\\ | |
| - | ==== Next Sound ==== | + | |
| + | ==== Next Sound Control ==== | ||
| 007: Play next sound fast\\ | 007: Play next sound fast\\ | ||
| 008: Play next sound slow\\ | 008: Play next sound slow\\ | ||
| Line 30: | Line 30: | ||
| 015: Play next sound low\\ | 015: Play next sound low\\ | ||
| - | ==== | + | ==== Volume/Pitch/Speed/Bend Control ==== |
| + | 020: Volume, X // sets Master Volume Level, accepts 0-127//\\ | ||
| + | 021: Speed, X // Play Speed, default 114, accepts 0-127//\\ | ||
| + | 022: Pitch, X // Pitch in Hertz, only for voiced sounds, default 88, accepts 0-255 (=32kHz..240kHz)//\\ | ||
| + | 023: Bend, X // Sets the Frequency Band (from deep hollow to high metallic), default 5, accepts 0-15//\\ | ||
| + | |||
| + | ==== Port Control ==== | ||
| + | 024: PortCtr, X // binaurally encoded output line control, see manual for details, default 7, accepts 0-7//\\ | ||
| + | 025: Port, X // port output value, see manual for details, default 0, accepts 0-7//\\ | ||
| + | |||
| + | ==== Phrase Control ==== | ||
| + | 026: Repeat, X // repeats the next code x-times, accepts 0-255//\\ | ||
| + | 028: Call Phrase, X // which EEPROM phrase to play, max 3 level deep nesting//\\ | ||
| + | 029: Goto Phrase, X // which EEPROM phrase to play//\\ | ||
| + | 255: End of Phrase | ||
| + | |||
| + | ==== Reset ==== | ||
| + | 031: Reset Defaults | ||
| + | |||
| + | \\ | ||
| + | ===== MSA Sound Codes ===== | ||
| + | 128..254: MSA Sound Phrases and Effects, see [[SpeakJet Definition List]]. | ||
| + | |||
| + | |||
| + | \\ | ||
| + | \\ | ||
| + | ====== SCP (Serial Control Protocol) ====== | ||
| + | SCP commands are executed immediately and provide control over the 5-channel synthesizer as well as accessing the internal speakjet EEPROM. | ||
| + | |||
| + | \\ | ||
| + | ===== Entering SCP ===== | ||
| + | '\0' to enter SCP | ||
| + | |||
| + | ==== SCP Commands ==== | ||
| + | 'H': Store Memory Type //accepts 0 and 32//\\ | ||
| + | * '0H': Write a register's value\\ | ||
| + | * '32H': Write to the internal EEPROM\\ | ||
| + | 'J': Memory Address\\ | ||
| + | * '0J': Envelope Freq\\ | ||
| + | * '1J': OSC1 Freq .. '5J': OSC5 Freq\\ | ||
| + | * '6J': Distortion\\ | ||
| + | * '7J': Master Volume\\ | ||
| + | * '8J': Envelope Control\\ | ||
| + | * '11J': OSC1 Vol .. '15J': OSC5 Vol\\ | ||
| + | 'N': Store Memory\\ | ||
| + | 'R': Clear Buffer\\ | ||
| + | 'S': Stop Enounciating\\ | ||
| + | 'T': Start Enounciating\\ | ||
| + | 'V': ACK\\ | ||
| + | 'W': Hard Reset\\ | ||
| + | |||
| + | \\ | ||
| + | ===== Exiting SCP ===== | ||
| + | 'X' or '\A'\\ | ||
| + | |||
| + | \\ | ||
| + | ===== Examples ===== | ||
| + | |||
| + | \0 V X*\\ | ||
| + | //Enters SCP-Mode, enounciates READY and exits SCP-mode// | ||
| + | |||
| + | 8J 0N 1J 500N 11J 16N*\\ | ||
| + | //1st OSC freq 500 and vol 16// | ||
| + | |||
| + | 0J 32H 01N*\\ | ||
| + | //write 0x1 to the first location of internal EEPROM// | ||
| + | |||
| + | 8J 00N*\\ | ||
| + | //set env-type to SAW// | ||
| + | |||
| + | 8J 10N*\\ | ||
| + | //set env-type to TRIANGLE// | ||
| + | //* Don't send spaces, this is just for readability!// | ||
speakjet_control_overview.1150034734.txt.gz · Last modified: 2006/10/15 09:35 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
